1. Interface size (key):
Refrigerant inlet and outlet: 28mm (1-1/8 inch) brazed joint, vertical in and horizontal out installation method
Bottom oil return port: 3/8 inch internal thread, built-in float ball valve for automatic oil return (float type oil return structure, no oil return during shutdown, automatic oil guide during operation)
2. Pressure and medium parameters:
Maximum design working pressure: 2.9MPa (29bar)
Pressure resistant burst pressure: 4.35MPa
Applicable refrigerants: commonly used refrigerants such as R22, R134a, R404A, R407C, R507A, etc
Separation principle: centrifugal impact+double-layer wire mesh interception composite separation
Oil separation efficiency: refrigerant residual oil rate ≤ 5ppm, minimal operating pressure loss (≤ 0.02MPa)
3. Flow and physical size:
Initial rated flow rate: 9.0 m ³/min
Outer diameter of cylinder: 140mm, total height approximately 499mm
Installation base: 4 fixed holes on the flange base
Shell material: Q235 carbon steel cylinder, outer wall anti-corrosion spray blue paint, internal rust prevention treatment
4. Performance and operating conditions:
Working environment temperature: -40 ℃~+120 ℃
Structural advantages: Large oil storage chamber capacity, avoiding compressor oil leakage; Float valve prevents refrigerant backflow
Certification: Pressure Vessel Compliance, General Safety Certification for Cold Storage Refrigeration Equipment
40-VA-5604，Oil Separator Specifications
| Refrigerant inlet and outlet | 28mm (1-1/8 inch) brazed joint, vertical in and horizontal out installation method |
|---|---|
| Maximum design working pressure | 2.9MPa (29bar) |
| Pressure resistant burst pressure | 4.35MPa |
| Applicable refrigerants | commonly used refrigerants such as R22, R134a, R404A, R407C, R507A, etc |
| Separation principle | centrifugal impact+double-layer wire mesh interception composite separation |
| Oil separation efficiency | refrigerant residual oil rate ≤ 5ppm, minimal operating pressure loss (≤ 0.02MPa) |
| Initial rated flow rate | 9.0 m ³/min |
| Outer diameter of cylinder | 140mm, total height approximately 499mm |
| Installation base | 4 fixed holes on the flange base |
| Shell material | Q235 carbon steel cylinder, outer wall anti-corrosion spray blue paint, internal rust prevention treatment |
| Working environment temperature | -40 ℃~+120 ℃ |
| Structural advantages | Large oil storage chamber capacity, avoiding compressor oil leakage; Float valve prevents refrigerant backflow |
| Certification | Pressure Vessel Compliance, General Safety Certification for Cold Storage Refrigeration Equipment |
About the 40-VA-5604，Oil Separator
The 40-VA-5604，Oil Separator is a oil drilling equipment used in industrial automation, control and power systems. It is rated at Refrigerant inlet and outlet 28mm (1-1/8 inch) brazed joint, vertical in and horizontal out installation method, Maximum design working pressure 2.9MPa (29bar), Pressure resistant burst pressure 4.35MPa. This oil drilling equipment is supplied as new, original industrial-grade stock. Each unit is identified by manufacturer part number 40-VA-5604，Oil Separator for accurate procurement and cross-referencing.
Why source the 40-VA-5604，Oil Separator from HDE123
- Verified part number: every 40-VA-5604，Oil Separator is checked against its manufacturer specification before shipment.
- 13 confirmed technical parameters available on this page for engineering review.
- Global delivery with clear lead time and commercial invoice for B2B buyers.
- Fast B2B support: send us the equipment model or an existing part number and our engineers confirm compatibility before you order.
Ordering the 40-VA-5604，Oil Separator
To order the 40-VA-5604，Oil Separator, add it to your cart and complete checkout, or use the Request a Quote form for volume purchases and replacement / cross-reference enquiries. Lead time: typically 3–10 working days for in-stock items, subject to confirmation. Worldwide shipping is available and a commercial invoice is provided for customs.